Gyratory fan in the use of the process of noise, so how should such a situation be resolved? I take you to understand. 1, in the pipeline outlet plus muffler to reduce the noise from the exhaust port leakage. 2, elbow size adjustment, increase elbow radius, to increase the elbow of the circulation diameter to reduce the flow rate, but will affect the normal installation space and efficiency and energy consumption. 3, the regulation of fluid process parameters, reduce the media flow rate can slow down or eliminate the impact of the fluid on the elbow section, but it is difficult to adjust, often does not work well. 4, increase the bracket, there is a certain effect, but not conducive to long-term use. 5, increase ...

Roots blower in the use of the process of water encountered in the situation, then how should this situation be dealt with? On this issue Roots blower editorial take you to understand. 1. Check whether the belt is damp, if it becomes loose, tighten it; 2. If the water quality is better, there is no suspended solids inside, you can directly drain the water after; 3. Check whether the motor is damp; 4. Replace the lubricant, 220# transparent gear lubricant; 5. If there is suspended matter in the water, must pay attention to clean up, not adhering to the impeller and other accessories; About “Roots blower into the water should be how to deal with it?” Roots blower editor will introduce you here, if...

Roots fan in the daily use of the process of meeting the problem is inevitable, then Roots fan common problems are those? On this issue, Roots fan editorial take you to understand. 1, about the three-leaf Roots fan air volume is insufficient: The method of filter blockage is to replace or clean the filter. Seal leakage treatment method to replace the sealing device. Rotor gap large processing method using tools to adjust the gap. 2, seal wear problem processing: Shaft bent or debris into the seal. Solution is to remove debris and perform shaft alignment. Rotor vibrates too much or bearing clearance is too large. The solution is to replace the bearing to eliminate deformation. Seal ...

Roots blower in the process of using the situation of high temperature, then what is the reason for this situation? Roots blower editorial take you to understand. (1) too much oil in the tank, too thick, too dirty; solution: reduce the oil level or hold the oil. (2) Filter or muffler blockage; Solution: remove the blockage; (3) The pressure is too high, too thick, too dirty. (3) pressure is higher than the specified value; Solution: reduce the pressure difference through the blower. (4) impeller excessive wear and tear, large gap; Solution: repair the gap; (5) ventilation; (6) the airflow is not good; (7) the airflow is not good. (5) ventilation is not good, the room temperature is high, resulting in high inlet temperature; Solution: open vents, reduce room temperature; (6) operation is not good, the room temperature is high. (6) running speed is too low, belt slippage. Solution: increase the speed to prevent belt slippage...

Roots fan in the process of operation there are those details need to be understood? On this issue, Roots fan small make up to take you to understand. 1. When starting or running, if you find that there is impact sound and sassafras sound, you should immediately stop the operation, eliminate the fault and restart. 2. It is forbidden to close all the import and export doors to start when it is put into operation. 3. When the Roots blower is running under rated condition, the temperature rise of each rolling bearing shall not be higher than 55℃, the maximum surface temperature shall not exceed 95℃, and the temperature of lubricating oil in the oil tank shall not exceed 65℃. 4. Check the firmness of each part frequently, especially the positioning pin, there can't be any loosening. 5. Regularly remove the dust of the filter or replace the filter media to avoid excessive dust content increase...

Roots blower in the use of the process of export temperature is very important for it, so today I bring you the Roots blower export temperature related to know the introduction. 1, if the roots blower is installed indoors. Condition can be installed air conditioning. Do not pity air conditioning and electricity costs. Because the motor temperature rises every 10 degrees, the life expectancy is reduced a lot. So indoor air conditioning, that can extend the life of the equipment, but also can reduce the export temperature. 2, if equipped with soundproof enclosure, in the summer must open the door of the soundproof enclosure. As far as I know, the domestic soundproof enclosure can not play a role in soundproofing, but to increase the ambient temperature, resulting in the temperature of the inhaled air on...

Roots fan in the process of using the ventilation fan network resistance calculation is not accurate, then what is the reason for this situation? Roots fan editorial take you to understand. The actual ventilation dust pipe pressure loss, for some reasons will be different from the calculation results, it is unavoidable, and thus the design specification of the calculation of the maximum allowable error of 10%-15%. Any neglect of this necessary program calculations, will have a significant impact on the operating efficiency of the ventilator to play a major impact must be given great attention. 1, ventilator pipe network resistance calculation of inaccurate rated value of the reasons: pipe network resistance calculation of sloppy and the use of resistance coefficient is not accurate enough; unreasonable...

Roots blower in the process of using the machine gear reducer is damaged, so what are the reasons and solutions for this situation? Roots blower small editor to take you to understand. 1. Roots blower gear shaft center installation is not correct, reducer large gear shaft and blower shaft, reducer pinion and motor shaft is not concentric, or the two gears are not installed in parallel, will cause vibration of the reducer. If the deviation of the different centrifuges is large, it will make the gear operation unstable and produce violent vibration, moreover, it will make the tooth surface subject to serious wear. If the two gears are not parallel, gear operation, there will be a localized “crappy” parts, and in serious cases, the teeth will be broken....

Roots blower in the use of the process of the temperature is too high, so how should this situation be resolved? Roots blower editorial take you to understand. (1) too much oil in the tank, too thick, too dirty; solution: reduce the oil level or hold the oil. (2) Filter or muffler blockage; Solution: remove the blockage; (3) The pressure is too high, too thick, too dirty. (3) pressure is higher than the specified value; Solution: reduce the pressure difference through the blower. (5) ventilation is not good, the room temperature is high, resulting in high inlet temperature; Solution: open vents, reduce room temperature; (6) operation is not good, the room temperature is high. (6) running speed is too low, belt slippage. Solution: increase the speed to prevent belt slippage...

Roots fan in the use of the process of friction now, so this situation is what causes it? How should it be solved? Roots fan editorial take you to understand. First, the reason (1) Pollution impurities on the impeller, resulting in too small a gap; (2) Gear wear, resulting in a large side clearance; (3) Gear fixation is not secure, can not keep the impeller synchronization; (4) Bearing wear causes the clearance to increase. Second, the solution measures (1) Remove the dirt and check the internal parts for damage; (2) Adjust the gear clearance, if the gear side clearance is greater than the average value of 30% ~ 50% should replace the gear; (3) Re-assembly of the gear, keep the taper with the contact surface ...

Roots blower in the use of the process of oil leakage, so what is the reason for this situation? How should it be solved? Roots blower editorial take you to understand. First, the friction between the impeller Its reason: there are impurities on the impeller, so it causes the gap between the impeller is too small; bearing wear and tear leads to an increase in the gap between. Solution: get rid of the dirt, and test the inner parts with or without other damage; adjust the gap between the gears. Second, Roots blower it's too high temperature Reason: too much oil in the oil tank of Roots blower, its filter is clogged; excessive wear of the impeller; poor ventilation, indoor temperature is too high, resulting in the temperature of the import...

Roots fan in the use of the process of safety is very important, so how much do you know about the safety of Roots fan? Roots fan editor to take you to understand. 1. It is strictly prohibited to close the inhalation side valve, if there are special circumstances have to close this valve, then, must stop the equipment operation. Because the equipment in the inhalation side of the valve is closed under the state of operation is likely to cause major accidents. 2. When turning the Roots fan by hand, you must stop the machine and cut off the power supply, at the same time, please pay attention to the fingers can not be rolled into the pulley. 3. The direction of rotation must be confirmed before operation. Reversing the direction of rotation may cause damage to the equipment. 4. When running the Roots fan, the belt cover must be installed first, after the belt cover is removed...

Roots fan in the use of the process of parts appeared in the process of serious wear and tear, so what is the reason for this situation? Roots fan editorial take you to understand. 1, the initial wear stage of the initial wear stage for the material wear stage, at this time between the blower parts on the surface of the unevenness of the place as well as the oxidation layer, decarburization layer, due to the operation of the Roots fan parts, the role of mutual friction is quickly smoothed. Roots fan due to the impeller in the body running without friction, do not need lubrication, so that the discharged gas does not contain oil. It is the ideal pneumatic conveying gas source for chemical, food and other industries. At this time, the equipment can show high productivity, but this period of time...

Roots blower in the use of the process of belt heating, so what is the cause of this? How should it be solved? Roots blower small editor to take you to understand. 1, leading to problems with the Roots blower belt is usually the cause of the belt is too loose, which will lead to the Roots fan belt heating. Manufacturers in the Roots fan factory should be adjusted to the fan before the belt to the right state of elasticity, so as to ensure smooth operation of the fan, too loose belt will not only lead to heat, but also the phenomenon of shedding damage. 2, too tight belt will also lead to belt heating, and will affect the fan linkage, loss in the power transmission process, too tight...

Roots fan in the use of the process of maintenance can not be less, then Roots fan should be how to maintain it? Roots fan editorial take you to understand. First, air cleaning, regular cleaning: pay attention to the surrounding environmental health, no debris around the fan or no oil, maintain good ventilation. In terms of air cleaning, regular cleaning of fan inlet sponge filter, and with the internal cleaning of the fan during maintenance, has been able to meet the fan's cleaning requirements and production requirements. Second, fan lubrication, lubricating oil to keep in the oil window red center position, such as adding too full will be with the fan running heat overflow, too little will damage the fan. Ensure the effectiveness of the lubrication facilities and lubricating oil is sufficient non...