Factory News | Changsha Tri-lobe Roots Blower Co.

Back to top

首页 » Factory News( Page 20 )

Factory News

Roots fan selection in the easy to ignore the issue of

Roots fan in the process of selecting those issues that must cause everyone to pay attention to it? On this issue, Roots fan small make up to take you to understand. 1, the transportation medium Roots fan can not directly transport more particles, impurities more media, such as high concentrations of oil and gas media, usually used to transport clean air. Secondly, the strong erosion of toxic gases can not be transported, mainly due to the sealing of the Roots fan, although the Roots fan at a certain level may wish to do 0 leakage, but time can not guarantee 0 leakage, once the leakage occurs, the toxic gases, flammable and explosive gas collars will be quite dangerous, so, can not be transported with the Roots fan, but also need to look at the transport...

The dangers of starting a Roots fan without venting

Roots fan is not emptied before use, then such an operation will bring those hazards to the Roots fan? On this issue Roots fan editorial take you to understand. ① motor! Motor voltage is unchanged, the speed is unchanged, the demand force is greater, do more work. Motor power increases, the current increases the current is too large, the protection system stop. No protection system motor burned out! ②Fan! Fan by the heat generated by the compressed gas, the heat can not be discharged in time! Fan heat, soften, brittle fan casing! Fan at the same time by two external forces 1, the motor on the fan spindle, bearings of the strong torsion. 2, the inner chamber of the air pressure on the fan casing of the outward push. Combined with heat and force, the fan cracked, or even exploded...

Solutions for oil leakage in Roots blowers

Roots blower in the use of the process of oil leakage, so what is the cause of it? How should it be solved? Roots blower editorial take you to understand. First, the friction between the impeller Its reason: there are impurities on the impeller, so it causes the gap between the impeller is too small; bearing wear and tear leads to an increase in the gap between. Solution: get rid of the dirt, and test the inner parts with or without other damage; adjust the gap between the gears. Second, Roots blower it's too high temperature Reason: too much oil in the oil tank of Roots blower and its filter is blocked; excessive wear of impeller; poor ventilation and high temperature in the room, resulting in high temperature of the inlet; Solution...

Introduction to the conditions of use of Roots fans

Roots fan in the use of the process of those conditions are you need to understand? On this issue, Roots fan editorial take you to understand. 1, the fan's working environment temperature shall not exceed 40 degrees Celsius, such as more than to take measures to cool down, otherwise shorten the service life of the fan. Fan outdoor configuration, please set up rain shelter. 2, the foundation design should be in line with the relevant provisions of the national machinery and equipment installation project, the foundation should be built on hard soil, it is appropriate to be 100-250 millimeters above the ground, the depth of 800-1500 millimeters. Foundation bearing surface should be wider than the base 100-250 mm, its foundation is not allowed to connect with other buildings and wall foundations foundation should be solid. Fan circumference...

Reasons for wear and tear on Roots fans

Roots fan in the use of the process of serious wear and tear, so what are the reasons for these situations? How should it be solved? Roots fan small editor to take you to understand. 1. The coaxiality error between the sealing ring and the shaft sleeve exceeds the standard. Solution: Replace the worn parts and adjust the coaxiality. 2. The shaft is bent. Solution: Straighten the shaft. 3. Hard chips enter the seal ring. Solution: Remove debris from the sealing ring. 4. Rotor vibrates too much. Solution: Improve operation and check rotor balance if necessary. 5. Excessive bearing clearance. Solution: Adjust the clearance or replace the bearing. 6. Deformation of the slide bearing. ...

Reasons why the air coming out of the Roots fan is hot

Roots fan in the process of work out of the gas is hot, so what is the reason for this situation? Roots fan editorial take you to understand. 1、Forced gas transportation Roots blower in the delivery of gas, the need for forced compression of the fan, fan selection, there is a pressure parameter, such as 39Kpa, Roots blower in the compressed air, the maximum pressure can withstand 39Kpa, the pressure of the pipeline in front of the party reached 39Kpa, the fan can overcome the pressure of normal operation. Forced compressed air operation, will inevitably generate heat, so the Roots blower exhaust fan out is with a certain temperature. 2, the inlet temperature Conveying clean...

Roots fan noise solution

Roots fan in the use of the process of noise, so what is the solution to the noise of the Roots fan? Roots fan editorial take you to understand. 1, import and export silencer transformation Roots fan import and export silencer must be retrofitted, and to use good quality silencer, silencer pipe wall should be thicker, so as to ensure the noise reduction effect of the silencer. 2、Soundproof room Generally speaking, if you want to significantly reduce noise, it is the use of soundproof room, the fan is placed in a small room alone, so as to achieve the best results, the soundproof room can be customized individually, according to our experience, the effect of the soundproof room is very good. For...

What do you know about Roots fan types?

Roots fan in the process of purchasing the first need to understand its type, so that you can choose a more suitable for their own Roots fan, about the type of Roots fan I take you to understand. 1, Roots fan in accordance with the different ways of working can be roughly divided into single-stage and double-stage points, of which there is only a compression stage of the blower, we call it a single-stage fan, and will be two single-stage fan in series, two consecutive compression of the gas fan we call it a double-stage fan. 2, according to the number of impeller head: two-leaf Roots fan and three-leaf Roots fan; 3, according to the use of points: kiln fan, gasification fan, aeration fan; 4、According to the type of medium: air...

Roots Blower Oil Change Details

Roots blower in the use of the process of oil change is unavoidable, then Roots blower in the process of changing the oil in those details need to be understood? Roots blower editorial take you to understand. 1, Roots blower lubricant volume assessment Roots blower oil amount of each model can always check the gear side of the oil mirror, in the shutdown to keep the oil level in the center line between. If the oil level is lower than the center position, you need to add lubricant in time, if the oil level is higher than the center position, oil leakage will occur. 2、Roots blower gear oil change order Clean out the gear oil first, inject new gear oil, start running for 300 hours, and then change the gear oil once every 1000 hours. 3、Roots blower...

Roots fan fan related knowledge introduction

Roots fan can not be separated from the fan in the process of use, so how much do you know about Roots fan related knowledge points? Roots fan small editor to take you to understand. 1, install frequency converter Installation of frequency converter, can adjust the motor speed, speed is an important factor affecting the fan air volume, frequency converter can adjust the motor speed, motor speed adjustment, fan air volume can be adjusted, generally in the case of fan without other failure problems, adjust the fan speed can change the air volume. 2, fan failure caused by the reduction of air volume, how to do? If the fan is faulty, resulting in insufficient air volume of the fan, you need to repair the fan first, for example: fan impeller wear...

Introduction to Roots Blower Operation Forms

Roots blower in the process of using the common form of operation there are 2 kinds, overload and normal load so about these 2 kinds of how much do you know? Roots blower small make up to take you to understand. First, the blower empty load test run. (1) new installation or overhaul of the fan should be empty load test run. (2) The concept of empty load operation of Roots blower: put into operation under the condition that the air inlet and outlet valves are all open. (3) Trial run should pay attention to observe the lubricating oil splash situation is normal, such as too much or too little should be adjusted oil. (4) There is no abnormal odor or smoke phenomenon and collision or friction sound, bearing parts of the radial amplitude is not greater than 0.08mm. 5) Air...

Roots blower belt slippage should be how to solve?

Roots blower in the use of the process of belt slippage, so how should this situation be resolved? Roots blower editorial take you to understand. In the absence of the same specification belt replacement, can only choose emergency treatment methods, such as boiling water hot belt or coating rosin method. Although useful, but can not deal with the fundamental problem. Will slip the belt cut, cut off 1 ~ 5 mm, and then cut the break into a beveled surface, cleaned with alcohol, and then with the Beijing production of 502 adhesive glue, placed l hours, such as drying can be used normally, it is worth paying attention to, it is necessary to use the Beijing YU main 502 adhesive, the other brand 502 dehydration is not easy to stick...

Reasons for overloading of Roots fans

Roots fan in the use of the process of overloading the situation, then what is the reason for this situation? How should we respond to it? Roots fan editorial take you to understand. First, the motor overload caused by system pressure changes Import filter clogging or other reasons for the equipment pressure increases, so that in the case of unchanged export pressure increases under pressure, the formation of negative pressure on the equipment resulting in motor overload. Roots fan equipment outlet system pressure increased resulting in motor overload operation, this situation requires equipment outlet system to check and thoroughly remove the cleanup. Second, the motor overload caused by abnormal equipment parts and components ① equipment gear out...

Roots fan impeller rust solution

Roots fan impeller in the use of the process of rust, then meet such a situation should be how to solve it? Roots fan small editor to take you to understand. 1. dismantle the inlet silencer of the Roots fan, the fan outlet with a blind plug, pour diesel fuel from the fan inlet until the diesel fuel submerged impeller, soak in diesel fuel for 24 hours. 2. release the diesel fuel, use a crowbar to remove the impeller from the fan. 2. Release the diesel oil, use the crowbar to gently pry the impeller back and forth from the fan inlet position until the impeller loosens, and slowly rotate the impeller until the fan impeller can smoothly rotate around in the fan chamber. 3. Clean up the residual diesel fuel inside the fan, install the triangle belt, and turn the car by hand to ensure that the fan can rotate smoothly for one turn. 4. ...
13755181118